Autel IM508 with XP400 Pro supports smart IMMO programming for BMW EWS3

Autel IM508 with XP400 Pro supports intelligent IMMO programming for BMW EWS3. The 2006 BMW E46 318i has been tested to successfully add the new key chip 44 using this advanced IMMO and key programming tool from Autel. The EWS3 adapter APB114 is required.

Preparation:
BMW E46 318i 2006
New blank chip: PCF7935
BMW key shell
Autel MaxiIM IM508 with XP400 Pro
EWS3 Adapter APB114 (from Autel IMKPA Key Programming Accessories Kit)
IM508 with XP400 Prosws3 adapter apb114

Autel-IM508-with-XP400-Pro-supports-smart-IMMO-programming-for-BMW-EWS3-1
Autel-IM508-with-XP400-Pro-supports-smart-IMMO-programming-for-BMW-EWS3-2

1. Connect EWS3 PCB, adapter, XP400 Pro and IM508
Uninstall EWS3 box from the car located in the driver can
bmw 318i e46 ews3 system

Autel-IM508-with-XP400-Pro-supports-smart-IMMO-programming-for-BMW-EWS3-3
Autel-IM508-with-XP400-Pro-supports-smart-IMMO-programming-for-BMW-EWS3-4

Connect Autel XP400 Pro with IM508 via USB cable
Note: cannot use with XP400
Supply 12V to supply CP400 Pro and EWS3 PCB
Connect XP400 Pro and EWS3 PCB with APB114
Connect internet to IM508

Autel-IM508-with-XP400-Pro-supports-smart-IMMO-programming-for-BMW-EWS3-5
Autel-IM508-with-XP400-Pro-supports-smart-IMMO-programming-for-BMW-EWS3-6

2. Step-by-step guide
Turn on MaxiIM IM508
Select Programming>> agree with the disclaimer>> Updating programmer files>> Chip (EEPROM. MCU, ECU)>> Chip Read & Write>> Immobilizer>> BMW>> EWS3- Kline>0D46J> R

Autel-IM508-with-XP400-Pro-supports-smart-IMMO-programming-for-BMW-EWS3-7

Read the operation guide on the screen carefully
The lamp on the XP400 Pro is always green during the operation.

Autel-IM508-with-XP400-Pro-supports-smart-IMMO-programming-for-BMW-EWS3-8

If the communication time out, please check connection and unplug then plug all cables again.
Select ALL>> SCHEMATIC DIAGRAM
See the on-screen operation guide and follow it to do step by step
Press ‘Read’
Wait a moment for reading
Save the file after reading

Autel-IM508-with-XP400-Pro-supports-smart-IMMO-programming-for-BMW-EWS3-9

Press ‘ESC’ back to menu
Select Write Key via Dump>> Europe>> BMW>> EWS3>> MC68HC11EA9

Autel-IM508-with-XP400-Pro-supports-smart-IMMO-programming-for-BMW-EWS3-10

Press ‘Loading data’ to load the last read EWS3 dump file
The data is ready, choose key position (key 3 unused) and press ‘Write Key’
Put the new blank chip: PCF7935 in the XP400 Pro programmer then press ‘Make Key’

Autel-IM508-with-XP400-Pro-supports-smart-IMMO-programming-for-BMW-EWS3-11

Wait a moment to write chip
Writing process is successful, and the key is ready
Disconnect EWS3 PCB
Put programmed chip into the key shell

Autel-IM508-with-XP400-Pro-supports-smart-IMMO-programming-for-BMW-EWS3-12

Plug EWS3 box back to cable under the steering wheel.
Insert the programmed key and try to start the car
OK! It works fine!

Be the first to comment

Leave a Reply

Your email address will not be published.


*